designed and manufactured in germany designed and manufactured in germany AXIOM1000 rev.1 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 1(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg specification AXIOM1000 rev.: 1 date: 2014-08-26 oscillator type: uhf ultra-low phase noise ocxo in connectorized package parameter min. typ. max. unit condition frequency range 300 1500 mhz standard frequencies 1000.000 mhz frequency stability initial tolerance @ +25c 300 ppb @ v c = 5.0 v vs. operating temperature range option 1 & 2 see tables 1 & 2 steady state vs. supply voltage variation (pushing) 10 ppb v s 5% vs. load change (pulling) 5 ppb r l 5% long term (aging) per day 1 2 ppb after 30 days operation long term (aging) 1 st year 100 200 ppb after 30 days operation frequency adjustment range electronic frequency control (efc) 1 2 ppm efc voltage v c 1.0 5.0 9.0 v efc slope ( ? f / ? v c ) positive efc input impedance 100 k rf output signal waveform sine wave load r l 50 5% output level +11 +13 +15 dbm (note 2) harmonics -40 -35 dbc sub-harmonics (multiples of f out /10) -45 -40 dbc (note 3) spurious -90 dbc warm-up time @ +25c 5 min ? f final /f 0 < 0.1 ppm phase noise @ 1000 mhz (note 4) -115 -143 -150 -110 -140 -145 -150 dbc/hz dbc/hz dbc/hz dbc/hz @ 100 hz @ 1 khz @ 10 khz @ 100 khz supply voltage v s 11.4 12.0 12.6 v (note 5) current consumption (steady state) 300 ma @ +25c current consumption (warm-up) 700 ma enclosure (see drawing) (lxwxh) 50.0x50.0x21.0 max. mm weight 60 g packing palette notes: 1. terminology and test conditions are according to ie c60679-1 and mil-prf-55310, unless otherwise stated 2. other output level on request 3. depending on frequency multiplication factor may be lower or higher than 10 4. please consult factory for phase noise of other fre quencies 5. other supply voltages on request
designed and manufactured in germany designed and manufactured in germany AXIOM1000 rev.1 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 2(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg absolute maximum ratings parameter min. max. unit condition supply voltage v s -0.5 v s + 10% v v s to gnd control voltage v c -0.5 15 v v c to gnd storage temperature -55 +125 c frequency stability vs. temperature stability lower temperature upper temperature option 1 [ppb] option 2 t [c] option 2 t [c] 05 5 0 0 a +50 10 10 1 -10 b +60 25 25 2 -20 c +70 50 50 3 -30 d +75 100 100 4 -40 e +80 200 200 5 -55 f +85 table 1 table 2 standard: 1b = -10c to +60c frequency stability [option 1] temperature range [c] 05 10 25 50 100 200 0 ~ +50 - o x x x x -10 ~ +60 - o x x x x -20 ~ +70 - o x x x x -30 ~ +70 - - o x x x -40 ~ +75 - - o o x x -40 ~ +85 - - - o x x -55 ~ +85 - - - - x x table 3 availability x = available, o = available on request, - not availa ble ordering code model option 1 [stability] option 2 [temperature range] revision frequency [mhz] AXIOM1000 table 1 table 2 rev.1 1000.000 example: AXIOM1000-25-1b_rev.1 C 1000.000 mhz handling and testing parameter procedure source handling and testing application note axan-011 www. axtal.com processing application note axan-012 www.axtal.com parameter procedure condition electrostatic discharge (esd) thd devices iec60749-26 hbm 2000 v smd devices iec60749-27 mm 200 v washable yes no rohs- compliant yes no
designed and manufactured in germany designed and manufactured in germany AXIOM1000 rev.1 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 3(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg enclosure drawing pin connections: pin # symbol function 1 v s supply voltage 2 gnd ground 3 v c control voltage (efc) sma rf out rf output * s ee a pplication n ote axan - 011
designed and manufactured in germany designed and manufactured in germany AXIOM1000 rev.1 www.axtal.com roemerring 9 drawing d0 fon: +49 (6261) 939834 d-74821 mosbach page 4(4) fax: +49 (6261) 939836 germany e-mail: info@axtal.com gmbh & co. kg environmental conditions test iec 60068 part iec 60679-1 clause mil-std- 202g method mil-std- 810f method mil-prf- 55310d clause test conditions (iec) sealing tests (if applicable) 2-17 5.6.2 112e 3.6.1.2 gross leak: test qc, fine leak: test qk solderability resistance to soldering heat 2-20 2-58 5.6.3 208h 210f 3.6.52 3.6.48 test ta method 1 test td 1 method 2 test td 2 method 2 shock* 2-27 5.6.8 213b 516.4 3.6.40 test ea, 3 x pe r axes 100g, 6 ms half-sine pulse vibration, sinusoidal* 2-6 5.6.7.1 201a 204d 516.4-4 3.6.38.1 3.6.38.2 test fc, 30 min per axes, 10 hz - 55 hz 0,75mm; 55 hz - 2 khz, 10g vibration, random* 2-64 5.6.7.3 214a 514.5 3.6.38.3 3.6.38.4 test fdb endurance tests - ageing - extended aging 5.7.1 5.7.2 108a 4.8.35 30 days @ 85c, ocxo @25c 1000h, 2000h, 8000h @85c other environmental conditions on request data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. revision history rev. drawing date [dd.mm.yyyy] remarks author checked 1 d0 26.08.2014 first issue hh hh
|
